Mercedes-Benz Forum

Mercedes-Benz Forum (https://www.benzforum.com/forum/)
-   Mercedes-Benz Sedans/Wagons (https://www.benzforum.com/forum/mercedes-benz-sedans-wagons/)
-   -   P0400 Code!!! (https://www.benzforum.com/forum/mercedes-benz-sedans-wagons/36723-p0400-code.html)

Dan Kasht 08-14-2019 06:20 AM

P0400 Code!!!
 
Hi all need help on a 2003 E320 sedan

I have had a p0400 code i cannot get rid of. I replaced EGR with new and removed and cleaned tube thoroughly. I changed a few of the vacuum lines that had wear and still no luck of ridding this code.

Any suggestions on where to look next?

RedLiner 08-14-2019 06:48 AM

Quote:

Originally Posted by Dan Kasht (Post 100691)
Hi all need help on a 2003 E320 sedan

I have had a p0400 code i cannot get rid of. I replaced EGR with new and removed and cleaned tube thoroughly. I changed a few of the vacuum lines that had wear and still no luck of ridding this code.

Any suggestions on where to look next?

Not sure if this helps

Noodles 08-14-2019 01:47 PM

Where the exhaust port is underneath the EGR valve is exhaust coming out?

If so the exhaust port needs to be cleaned. Please post back so I can post the instructions if needed.

Dan Kasht 08-14-2019 07:57 PM

Redliner: I watched that video before. I changed a few hoses that were bad. I see a hose deep behind that pressure sensor/secondary air pump(not sure if cracked). Does that go to vacuum system? Is this the one he is talking about in the video?

Noodles: I replaced the EGR with a new unit and cleaned the pipe reaallly well. Where the egr is connected to the exhaust, i did not clean. I do not see any smoke anywhere. Do you think i need to clean this? Can i just take thee egr off again and spray down there? If you have instructions i would really appreciate it.

Is there anything else that would make p0400 show up?

O yeah on a side note, i did clean the breather and reseal on the passenger side valve cover. I did not do the driver side. Is this a possibility?

Thank you !

Noodles 08-15-2019 01:25 PM

See this post from our sister site. From around post #140 it goes into detail about plugged ports.

https://www.benzworld.org/forums/w16...tem-diy-8.html

chevota 08-15-2019 09:06 PM

I wish this was a possible solution, but I had that same eng but in '99, and same code. Never figured it out... Solution was to get rid of the car.
I can only recall three car problems in my life that I could never figure out, this was one. Another was also a Benz with that same eng, same year as yours where it would die when put in gear until warmed up. Dealer couldn't figure that out either. Solution was to feed it hot air piped from the ex manifold via a clothes dryer duct. the eng didn't need to be hot, it just needed hot air! The other was driveshaft vibration (not Benz) that I dragged around with me for 20 years despite changing out so many parts over the years that it was literally a different vehicle. Now, several years later, the exact same vibe reappeared in my latest Benz.... Like before, everything looks/feels perfect, yet there it is. So while I love Benz overall, they can vex me and I may have to get rid of this one too.
Btw I scoured the web and every local Benz shop and dealer for a solution to the p0400 issue, which was in fact working perfectly. The dealer claimed to have never seen the issue, but I've heard that all my life about anything I have problems with. The dealer could not even tell me what in the programming trips p0400 so basically zero clues where to look other than what seems obvious.
If you find it, please post so others in that situation have something to go on. Best of luck to you...

Noodles 08-16-2019 08:39 AM

Cleaning out the ports does work. I have had success using the BG 221 and a small brass gun cleaning brush.
That was over 100,000 miles ago and the problem has stayed away.

Dan Kasht 08-18-2019 07:42 AM

Interesting, thank you. Question. I initially had the p0171 code for secondfary air pump. When i went to check this code i found a broken piece of vacuum line between the air pumps (i think this is what they are called) and replaced. It made that code go away and thats when this p0400 showed up. Do you think it could be the air pumps? Is there a way to test these?

Noodles 08-19-2019 11:16 AM

There is only one AIR pump. It is in the center at the top front of the engine. If the P0171 code has not vom back then it is fine.
One or both of the exhaust ports that receive air from the pump is more than likely blocked. It is a know issue with the M112 V6 and M113 V8 engines.

Chasen 12-26-2019 03:37 AM

it seem there still some problem on your vehicle related p0400,only after repair all problem then clear it.


All times are GMT -6. The time now is 04:43 AM.

Powered by vBulletin® Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
© AutoGuide

 
For the best viewing experience please update your browser to Google Chrome